Sensonic D-2 prepares gas sample for the co-operating analyser by removing dust, salts particles and condensate, so the sample is dry and clean. Using gas conditioner is essential in case of majority measurements with gas analysers.

Brochure

Features

  • Gas probe pipe
  • Initial heated filter
  • Heated hose that supplies gas sample to the analyser’s drying module(s)
  • One or two drying modules
  • Final filters that cleans the dried gas sample
  • Gas pump
  • Condensation pump (only when Sensonic D-2 is equipped with condensation type dryer with Peltier element)
  • Ventilation valve that provides clean air for cooperating analyser

Single Nafion dryer


Single condensation (Peltier) dryer


Nafion dryer + condensation dryer


Dual condensation dryer

Tech specs

Sensonic D-2 gas dryer with single condensation dryer
Dimensions (W x H x D) 500mm x 340mm x 150mm
Weight 12kg ÷ 13kg
Operating conditions T: 0°C ÷ 50°C, RH: 5% ÷ 90% (non-condensing)
Dryer type Based on Peltier cooling element with fan (12VDC supply)
Drying method Water condensation by rapid cooling down
Cooling temperature 0°C ÷ 20°C
Ready to operate after 5 minutes
Storing temperature 0°C ÷ 60°C
Maximum gas flow for efficient drying (at inlet gas temp. 100°C and RH 100%) 100l/h
Gas filters: quantity | material 2 | PA – body, PC – cover, viton – sealing
Filter insert: length | ID | OD | material | pore size 32mm | 12mm or 15mm | 18mm or 20mm | PE | 5 μm
Condensate removal With built-in peristaltic pump
Peristaltic pump capacity 38ml/min
Power supply: input | maximal power consumption 230V AC | 40W (without heated hose)
Heated hose temperature +180°C electronically stabilised
Heated hose temperature hysteresis ~ 5°C
Heated hose length 3m (optionally 5m or 10m)
Heated hose power supply: Input | maximal power consumption 230V AC | 1000W
Heated hose thermocouple wires K-type (S-type optionally)

Sensonic D-2 gas dryer with single Nafion® dryer
Weight 9kg ÷ 10kg
Dryer type Based on Nafion® exchanger
Drying method Water transfer through Nafion® membrane driven by partial vapour pressure differential – first order kinetic reaction
Cooling temperature n/a
Ready to operate after 1 minute
Under pressure in Nafion® collar ~500mbar

Sensonic D-2 gas dryer with Nafion® dryer + condensation dryer
Weight 11kg ÷ 12kg
Dryer type
  1. Based on Nafion® exchanger
  2. Based on Peltier cooling element with fan (12V DC supply)
Drying method
  1. Water transfer through Nafion® membrane driven by partial vapour pressure differential – first order kinetic reaction
  2. Water condensation by rapid cooling down
Cooling temperature
  1. n/a
  2. 0°C ÷ 20°C
Ready to operate after 5 minutes

Sensonic D-2 gas dryer with dual condensation dryer
Weight 12kg ÷ 13kg
Cooling temperature First dryer: Constant, about +1°C, output gas dewpoint about +4°C; Second dryer: 0°C ÷ 20°C
Ready to operate after 5 minutes

Drawing

Drawing #1
Gas filter of Sensonic D-2 dryer (high header type) - Z10-FILTER-001.
Drawing #2, #3
Gas filter of Sensonic D-2 dryer (low header type) - Z40P-FILTER-03, Flow indicator (610A0001B)
Drawing #4
Flow indicator (610A0001B)
Drawing #5
“Probe” connector (Binder 680 series, 7-pin female) - 512O0710C
Drawing #6
Filter set fitting (615A0003C)
Drawing #7
Heated hose connector (Binder 694 series, 13-pin female) - 512O1300A
Drawing #8
Heated hose magnetic fitting (male part)